www.imoc.co.uk

excellent mate, cheers!

It seems that my reverse lights blowing is caused by the reverse light switch located on the gearbox.. well coming from a couple of mech i know.. I just had a clutch change so maybe thats when it happened.. I could change/fix it myself if i knew where it was or i could bring it back to the mech that...

anybody have any ideas?

Hi, ive just installed an apexi boost gauge via the cig lighter poer, earth and cig lighter light for illumination. Since then my reverse lights keep blowing!? i changed them out earlier and tried them with the car on two clicks and in r gear, to which they worked. After driving around and trying th...

Ive just got one of these second hand. Once i fitted it, I was getting the flutter sound on full boost so i adjusted the spring until it was a solid possssst on boost and a mix of the two in normal non-boost pre 3000 revs. the prob is, every photo ive seen of other peoples setup the spring is nearly...

ultimate brute force sorted it.

just to bleed brakes now

cant get the pass rear disk off!!! grrrrr

Got the front s-techs and droplinks done. The nuts and bolts were nice and easy to remove. To be honest the first side took 3 hours to do due to me being careful...prob too careful. the opp side took 30mins lol! One thing I didnt expect was the weight you have to put on the hub to get tit to slot ba...

thanks very much for the input. hopefully everything goes well.

im gonna photo-log it all anyway and place the pics up for future attemptees

Ive next week off and i have a box of s-tech springs, new droplinks, braided lines, disks, pads, new lights, oil filter and oil.

Im gonna do the springs first. Any input for the DIY mech?

thanks for the response

thanks, i waited until i got home that day to find the part number. i couldnt access the site from my work computer.

At least one person got back to me.

Hi, prior to geting a new clutch, decat and driveshaft installed i ran my MCB at .8/9 bar. The car boosted fine. Today, when i picked the car up the mech said i should turn my boost down because it is up to high and causing the engine to cut-out. on the way home i boosted the car and once giving it ...

Hi It turns out i need four of the 6 bolts that go into the drivers side driveshaft. Can anybody tell me the part number for these bolts. the bgb link is below and should be of help. **Im in work and cant access 'personal sites' through our internet** Thanks http://www.mr2-tech.com/bgb/mechanical/vo...

After changing my dash bulbs to red 501s (inc the fuel light), the fuel light is on all the time. I havent yet taken the dash apart again to investigate, but could the bulb voltage being low i.e modern low voltage led cause it to come on all the time? when my new boost gauge comes ill be stripping i...

This looks good!

APEXI 60mm Gauge £36

http://cgi.ebay.co.uk/ws/eBayISAPI.dll? ... ink:top:en

thanks dude.

there is a real crunch when the wheel rotates....sounds horrible.

Its being picked up tomorrow and brought to a mach for the clutch change planned for today. Changing the clutch will actually give better access to this prob.

Ill update, with the fix.

Thanks, i havent got a photo yet as it was dark when i got home last night and i have no torch (maplins today!!) the bolt that is missing is the left hand side one of the two black bolts on the driveshaft in this picture. i will get an actual real picture today. http://www.mr2turbo.info/pics/rearsus...

I was driving along today on my way to work and sweeping right through a round-about before entering a motorway i heard a 'clicking' sound thenn a big 'glunk' from the drivers rear area. i pulled over on to layby and checked under the car. There didnt seem to anything out of place or obstructing so ...

JAPSPEED FTW