It is coming from the turbo area and goes away once warm.
http://youtu.be/SWoqEUpCrOE
[Mk2] [Turbo] Help needed, does anyone know what this noise is?
Moderators: IMOC Moderators, IMOC Committee Members
Re: [Mk2] [Turbo] Help needed, does anyone know what this noise is?
Sounds very much like the exhaust manifold gasket is blowing. First step is to try and get a spanner on all the nuts to check that they're tight.
It goes when warm as the manifold expands slightly to seal the gap
It goes when warm as the manifold expands slightly to seal the gap
Re: [Mk2] [Turbo] Help needed, does anyone know what this noise is?
It almost sounds like a belt is slipping. There is a nut missing from my downpipe.
Re: [Mk2] [Turbo] Help needed, does anyone know what this noise is?
Bone wrote:There is a nut missing from my downpipe.
Replace that as a first port of call and I'd be pretty sure the noise will go straight away.
Re: [Mk2] [Turbo] Help needed, does anyone know what this noise is?
It sounds more like the inlet side of the turbo. Could it be the turbo?
Last edited by Bone on Mon Aug 01, 2011 9:06 pm, edited 1 time in total.
Re: [Mk2] [Turbo] Help needed, does anyone know what this noise is?
You won't know until you replace that nut
Seriously, replace the nut and see where you go from there. There's no point worrying unduely until you've done that.
Seriously, replace the nut and see where you go from there. There's no point worrying unduely until you've done that.
Re: [Mk2] [Turbo] Help needed, does anyone know what this noise is?
are you sure thats not the exhaust wheel scraping the housing.
Re: [Mk2] [Turbo] Help needed, does anyone know what this noise is?
That's what I thought it could be.
Re: [Mk2] [Turbo] Help needed, does anyone know what this noise is?
downpipe off and have a butchers matey...better to know now though eh
Re: [Mk2] [Turbo] Help needed, does anyone know what this noise is?
Downpipes coming off tonight. Will report back.
Re: [Mk2] [Turbo] Help needed, does anyone know what this noise is?
All manifold studs are tight.
I went to remove the downpipe and found 1 nut missing, 1 nut spun loose (right at the other end of the thread) and the others weren't that tight.
I removed the downpipe and inspected and felt the exhaust turbine and all seamed O.K, spun nice and smooth and only minimal side to side play.
I then started it up! It was loud and im not sure if this sounds normal or not. Please give me your opinions. Cheers.
Toby.
http://youtu.be/6eFvmHOZ0Nw
I went to remove the downpipe and found 1 nut missing, 1 nut spun loose (right at the other end of the thread) and the others weren't that tight.
I removed the downpipe and inspected and felt the exhaust turbine and all seamed O.K, spun nice and smooth and only minimal side to side play.
I then started it up! It was loud and im not sure if this sounds normal or not. Please give me your opinions. Cheers.
Toby.
http://youtu.be/6eFvmHOZ0Nw
Re: [Mk2] [Turbo] Help needed, does anyone know what this noise is?
Downpipes coming off tonight. Will report back.
-
- Posts: 7172
- Joined: Thu Dec 16, 2004 6:39 pm
- Location: Oldham
Re: [Mk2] [Turbo] Help needed, does anyone know what this noise is?
Blowing from, more than likely, exhaust manifold gasket. It's not your turbo at fault so don't worry! Are all the manifold studs tight? Also, not bottomed out on rust so feels tight. Then check turbo to manifold is tight, and turbo to downpipe.
476bhp & 415ft lb @ 1.9bar Magic by Ryan!
Gone, but never forgotten
Now with a mk1.5 & a NHB EP3
Gone, but never forgotten
Now with a mk1.5 & a NHB EP3
Re: [Mk2] [Turbo] Help needed, does anyone know what this noise is?
Problem solved It was the exhaust manifold gasket as 1 stud had broken. I striped it all down and replaced 4 studs all the nuts and gaskets. She now runs sweet as a nut