Confirming I still want the hoses. Blue, stock I/C.
Got the Mikalors for the car a couple of months ago though.. The stock clips had threaded.
Any idea of when? Before or after Xmas?
Silicone hose kits (Turbo - inlet piping)
Moderators: IMOC Moderators, IMOC Committee Members
-
- Posts: 3835
- Joined: Wed Dec 15, 2004 1:15 pm
- Location: Sh*tting a Rainbow!
- Contact:
Re: Silicone hose kits (Turbo - inlet piping)
how do we measure the pipes??????
i have 2 reducers on my IC.......
Ruler or tape measure, be as accurate as possible. Measure each end in a X so you get two measurments for each end. Make sure the hose is round and not distorted.
Give me in the internal diameter, extenal diamater of both ends and the overal length of the hose.
A few others have the 205 cc so their measurments may be right but its best to check.
Cheers
James
Re: Silicone hose kits (Turbo - inlet piping)
Bender Unit wrote:how do we measure the pipes??????
i have 2 reducers on my IC.......
Ruler or tape measure, be as accurate as possible. Measure each end in a X so you get two measurments for each end. Make sure the hose is round and not distorted.
Give me in the internal diameter, extenal diamater of both ends and the overal length of the hose.
A few others have the 205 cc so their measurments may be right but its best to check.
Cheers
James
i can do that......
regarding the title of the thread tho, what other pipes can we do, as the title says turbo hoses, not IC/CC hoses.........
or is this defo an ic/cc hose only thing?????????
-
- Posts: 3835
- Joined: Wed Dec 15, 2004 1:15 pm
- Location: Sh*tting a Rainbow!
- Contact:
Re: Silicone hose kits (Turbo - inlet piping)
Check the other thread feller, I have talked the company into producing other stuff for us depending on interest.
Cheers
James
Cheers
James
Re: Silicone hose kits (Turbo - inlet piping)
Bender Unit wrote:Check the other thread feller, I have talked the company into producing other stuff for us depending on interest.
Cheers
James
fella, do you need these measurements in mm? inchs? cm?
obviously it helps if everyones using and measuring the same way.....
obviously a good idea to double check peeps tb and turbo/ic pipe measurements are the same.....as these dont change do they (unless you got a different tb, or turbo pipe to everyone else).....
Re: Silicone hose kits (Turbo - inlet piping)
You will have to make sure what everyone is measuring too, either inner diameter or outer diameter.
Re: Silicone hose kits (Turbo - inlet piping)
i just measured mine, however, i didnt actually take any of my pipes off.....
it would of ment completely taking out my greddy ic, and after the aftermath of putting it in, i wernt gona try, lol........
if everyone just measures the circumference, and length, im sure thats enough....its not hard to work out the diameter based on the thickness as well....
outer diameter = circumference divided by pie......
inner diameter = (outer diameter) missues 2xthickness........
all pipe measurements are in 1/4inch increments i think, so everyone should be similar really........
it would be handy also mate to get good solid clips, you know the bolt and bar ones.....
greddy i/c ones are 46-70mm clips btw.......
it would of ment completely taking out my greddy ic, and after the aftermath of putting it in, i wernt gona try, lol........
if everyone just measures the circumference, and length, im sure thats enough....its not hard to work out the diameter based on the thickness as well....
outer diameter = circumference divided by pie......
inner diameter = (outer diameter) missues 2xthickness........
all pipe measurements are in 1/4inch increments i think, so everyone should be similar really........
it would be handy also mate to get good solid clips, you know the bolt and bar ones.....
greddy i/c ones are 46-70mm clips btw.......
Re: Silicone hose kits (Turbo - inlet piping)
You have a PM with my order confirmation mate
Re: Silicone hose kits (Turbo - inlet piping)
pm'ed. im in for a set of purple ones for my stock rev1 =D>
due to my car being a complete pain in the xxxx. gotta pull out. this time for definate tho big bill is a coming
due to my car being a complete pain in the xxxx. gotta pull out. this time for definate tho big bill is a coming
-
- Posts: 3835
- Joined: Wed Dec 15, 2004 1:15 pm
- Location: Sh*tting a Rainbow!
- Contact:
Re: Silicone hose kits (Turbo - inlet piping)
Still waiting on people to confirm what they want, give me dimensions etc.
I need the internal diameter, external diameter and length. Any hoses made up from the circumference could possibly result in being an incorrect fitment.
Can people please confirm what they want.
I need the internal diameter, external diameter and length. Any hoses made up from the circumference could possibly result in being an incorrect fitment.
Can people please confirm what they want.
-
- Posts: 7069
- Joined: Thu Feb 03, 2005 5:23 pm
Re: Silicone hose kits (Turbo - inlet piping)
Bender Unit wrote:
Can people please confirm what they want.
PM from me will follow this evening - Sorry for the delay James
Car now Sold damn 5th Lumber Disc !
Re: Silicone hose kits (Turbo - inlet piping)
WHAT MEASUREMENTS DO YOU NEED??
cm, mm, inchs?
i did pm bout this but i didnt get a reply fella....
also, am i the only one with the greddy ic here, just want to compare measurements....
cm, mm, inchs?
i did pm bout this but i didnt get a reply fella....
also, am i the only one with the greddy ic here, just want to compare measurements....
-
- Posts: 1475
- Joined: Wed Nov 02, 2005 2:00 pm
- Location: Surrey
Re: Silicone hose kits (Turbo - inlet piping)
Hi I would like a set also.
94 MR2 GT-S Turbo Rev3 and in the blue please. Standard I/C
Cheers Reece.
94 MR2 GT-S Turbo Rev3 and in the blue please. Standard I/C
Cheers Reece.
Last edited by Caribbean_Blue on Thu Dec 01, 2005 1:13 pm, edited 1 time in total.
Running: 313.8BHP @ fly and 285lb torque on 1.15bar.
MY MR2 FOR SALE: http://www.imoc.co.uk/forums/viewtopic.php?t=109986
MY MR2 FOR SALE: http://www.imoc.co.uk/forums/viewtopic.php?t=109986
-
- Posts: 1949
- Joined: Tue Dec 14, 2004 9:26 pm
- Location: Lancashire
Re: Silicone hose kits (Turbo - inlet piping)
Am i right in saying that you get 4 hoses in this kit?
Is the offer still on or have i missed the boat. Im after a set for my rev 3 tubby in red, the intercooler/tb inlet hoeses, am i after the right ones?
Is the offer still on or have i missed the boat. Im after a set for my rev 3 tubby in red, the intercooler/tb inlet hoeses, am i after the right ones?
-
- Posts: 3835
- Joined: Wed Dec 15, 2004 1:15 pm
- Location: Sh*tting a Rainbow!
- Contact:
Re: Silicone hose kits (Turbo - inlet piping)
Known details
I will see if I can move this initial batch on as you have all confirmed what you want and I have the measurments.
keith.mcclorry Rev2 Blue (Stock IC)
stevel - Rev3 - Blue (Stock IC)
JohnA Rev1 Red (Stock IC)
misterT Rev2 Red (Stock IC)
Nige_B Rev2 Red (Stock IC)
Jode Rev3 Yellow - (Stock IC)
Muffleman Rev1 Green - (Stock IC)
Hurstie1981 - Rev3 - Red - (Stock IC)
Reecey690 - Rev3 - Blue - (Stock IC)
Stu Wilson Rev2 Red - (Stock IC)
Different ICs need to supply measurements
I need measurments in MM, I need the diameter, the pipe thickness and the lengths.
If one guy with the ST205 CC kit so if one measures the parts then it should suit all. As there is only 2 pipes involved this kit will be cheap. Can someone show me a pisture of thie ST205 CC install? Guys with the greddy and ARC I really need the internal diameters to ensure a proper fit.
DannyW Rev? - Blue (Different IC)
Need pipe ID/OD and Length for different sections (ARC IC)
CosmosblueMR2 Rev3 Purple (Different IC)
Need pipe ID/OD and Length for different sections (ST205 CC)
jimGTS Rev2 Red (Different IC)
Need pipe ID/OD and Length for different sections -(Greddy IC)
rwilson_ie Rev3 Colour? (Different IC)
Need pipe ID/OD and Length for different sections (ST205 CC) ?? Still in?
Outstanding details people havent confirmed etc - will be deleted shortly.#
Gaz6002 Stock / CC? Colour? (Different IC)
Need pipe ID/OD and Length for different sections (ST205 CC)
bidtowin Rev? Colour? - (Stock IC?)
mr2turbo117 Rev? Colour? - (Stock IC?)
Stu Wilson Rev2 Red - (Stock IC?)
I will see if I can move this initial batch on as you have all confirmed what you want and I have the measurments.
keith.mcclorry Rev2 Blue (Stock IC)
stevel - Rev3 - Blue (Stock IC)
JohnA Rev1 Red (Stock IC)
misterT Rev2 Red (Stock IC)
Nige_B Rev2 Red (Stock IC)
Jode Rev3 Yellow - (Stock IC)
Muffleman Rev1 Green - (Stock IC)
Hurstie1981 - Rev3 - Red - (Stock IC)
Reecey690 - Rev3 - Blue - (Stock IC)
Stu Wilson Rev2 Red - (Stock IC)
Different ICs need to supply measurements
I need measurments in MM, I need the diameter, the pipe thickness and the lengths.
If one guy with the ST205 CC kit so if one measures the parts then it should suit all. As there is only 2 pipes involved this kit will be cheap. Can someone show me a pisture of thie ST205 CC install? Guys with the greddy and ARC I really need the internal diameters to ensure a proper fit.
DannyW Rev? - Blue (Different IC)
Need pipe ID/OD and Length for different sections (ARC IC)
CosmosblueMR2 Rev3 Purple (Different IC)
Need pipe ID/OD and Length for different sections (ST205 CC)
jimGTS Rev2 Red (Different IC)
Need pipe ID/OD and Length for different sections -(Greddy IC)
rwilson_ie Rev3 Colour? (Different IC)
Need pipe ID/OD and Length for different sections (ST205 CC) ?? Still in?
Outstanding details people havent confirmed etc - will be deleted shortly.#
Gaz6002 Stock / CC? Colour? (Different IC)
Need pipe ID/OD and Length for different sections (ST205 CC)
bidtowin Rev? Colour? - (Stock IC?)
mr2turbo117 Rev? Colour? - (Stock IC?)
Stu Wilson Rev2 Red - (Stock IC?)
Last edited by Bender Unit on Mon Dec 12, 2005 11:23 am, edited 1 time in total.
-
- Posts: 191
- Joined: Fri Dec 17, 2004 1:15 pm
- Location: Durham
Re: Silicone hose kits (Turbo - inlet piping)
rev2 ,red,stock I/C
turbo hoses
If these are still available I'd like a set in blue for a rev.2 on a std. I/C.
Let me know about payment.
JB
Let me know about payment.
JB
Re: Silicone hose kits (Turbo - inlet piping)
Spacey, rev3, standard IC, black
will also need hoses for the greddy IC once it arrives.
will also need hoses for the greddy IC once it arrives.
Re: Silicone hose kits (Turbo - inlet piping)
If this is still going would like a set in purple for a stock Rev1
Cheers,
Steve
Cheers,
Steve
-
- Posts: 3835
- Joined: Wed Dec 15, 2004 1:15 pm
- Location: Sh*tting a Rainbow!
- Contact:
Re: Silicone hose kits (Turbo - inlet piping)
Guys this will go ahead, sorry for the delay a family berevement has mean lots of stuff has been put on the back burners.