www.imoc.co.uk

skinthespin wrote:Have a read of this mate

http://www.imoc.co.uk/forums/viewtopic.php?p=473241

dont put 235's on a 7 inch rim!!!

Yes I know they are a bit wide for them but they look ok and grip very well, no problems at all.

Bob

wazza2 wrote:Thats good. There was a small amount from side to side, about 1mm and none back and forth.

1mm is a lot, it should only move a very small amount side to side.
The oil is from the breather pipe.

Bob

This may sound silly those who know, but can you then run WI AND N2O? not together per say, but WI set up on an boost trigger, so when the boost hits say 0.8bar it sprays to reduce chances of det ? (i have a separate water tank and pump in the boot and a few washer jets that spray on my IC at the m...

I have 235/40/17 on the rear on 7" wheels, fit ok and work very well.

Bob

Jimbob wrote:Yes

Then your problem is that the HP pump is flowing more fuel than the LP pump, thats the wrong way round.
What pumps do you have?

Bob

Hi bob. Thanks for the information. Looks like its not chipped then :( The turbo is running at 13psi. I am interested in buying your ECU, let me know if you decide on selling it. What sort of performance increase can I expect from fitting it? Regards Ross You will need to check the info on the Blit...

The MR2 ECU is not one that can be chipped as such. You have to have an add on ECU and you would be able to see that next to the standard ECU. I have a Blitz ECU I may be going to sell if you do want to upgrade.

Bob

So where did you get them from and what was the price? Are they full and dip beam?

Bob

This is a good read guys! I have a mate who does tuning and I asked him a while ago about WI and he said it was pointless except to stop det and there's other things (as said) that can be done to prevent det without losing power. I don't know. I'm still in 2 minds whether to get WI and just see for...

P.S That article is only associated with the addition of water not the cooling of fuel. Cooling the fuel can only do two things. 1 change the mixture, make the engine richer or leaner 2 cool the incoming air, just the same as some believe water injection can do. A rich mixture or water will do the ...

Yes I will, and about the speedo too.
Thanks for all the help.
Bob

3S Service Centre wrote:the driveshafts are the same and it will fit assuming both are lsd or both are not.

Thanks. I hope you are right. Will find out over Xmas.

Bob

Found this write up, it tells how it all works For those who think that water, water/methanol, or excessive (rich) fuel injection is done to cool and make more dense the intake air before it enters the cylinders by taking advantage of the latent heat (absorption) cooling effect as the liquid undergo...

Oh no James; no good ideally one wants ice cold fuel a bit like water injection the colder the more power which you know any way! But if any one does know how to make fuel colder I would consider doing it! An unexplored avenue to the average general tuning ethos! :wink: Hope you get it sorted/ have...

Will a Rev 1 turbo gearbox fit in a rev 2? Are the drive shafts the same and will the Rev 2 fit in the Rev1 box?
All info will help.
Thanks

Bob

mattcambs wrote:

bobhatton wrote:
All fuel is now unleaded!!!!!!!
What is optimax then, I did think it was only 97ron

I guess not much demand for high RON fuels in tractor country?

Thats right, no tesco 99 down this way.
Bob

probably been done to death I know, but I havn't been on here for a while, anyway I read on another toyota site ( toyota owners club ) I think its called . and some guy reckons running your turbo'd mr2 on unleaded for years can cause damage to your turbo and put it in ''safe mode'' aswell to stop d...

I had 16" but could not get the right tyres I wanted for the rear as they had stopped making that size so had to go to 17". So check you can get the size tyre you want from the makers you like.

I have a low mileage used one spare if your interested? I bought it to use it but came across a tilton :D IIRC most of rogues top cars use the os giken twin plates. Michael. Michael I have been looking at the Tiltons, what one do you use and who did you buy it from. We have 3 cars all with slipping...

Hello, On ebay I see some Blitz ECU's for sale. Are these ECU's an improvment for the engine power? I self have an 3SGTE Gen2 engine. Does anybody know which ECU i need. I see a lot of different types. I want to know which partnumber i need. The first number is PC-23710T but the numbers below that ...