www.imoc.co.uk

Thanks for the tips. I'll make sere to check what you mentioned, dont want this set to warp. Its driving me crazy. I've just ordered a set should be with me soon.
Cheers
Tony

As the title says my front discs are knackered. Im just looking for some regular non drilled or grooved items. Anyone got any opinion on these.
http://cgi.ebay.ie/TOYOTA-MR2-2-0i-inc- ... dZViewItem

As the title says I lowered the car with these http://cgi.ebay.ie/ws/eBayISAPI.dll?ViewItem&item=140083893670. Now since putting them on every time i go over a speed bump I hear a metallic click which sounds like it coming from the front right. I have taken that side back off and it looks like t...

Thanks for the replies. Kinda have my heart set on the lexus lights so i think the're a definite. Rev 3+ are hard to come by pintovit kinda like the clean look of the lexus ones. Will post pics of the clear lights when I get them. :thumleft: Marc you are right about the carbon centre peice I'll make...

Ok here's the story. I've recently come into a few quid and have looked after the bills n loans n xxxx. I have some money left over and am thinking about updating my standard rev 1 n/a. Not going down the engine tuning road beyond a decat and induction kit (for the sound more than anything else) as ...

Thanks for the replys. I've no problem grinding down the studs by a few mm if necessary. Not sure if my wheels have the slots mentioned cut into the back of the hub i'll check when i'm tackling the job. Either way its no big deal to crack out the grinder. Just a tip for anyone looking at this in the...

Im looking at getting these spacers http://www.icetronix.com/index.aspx?page=display_product&category=spacers&id=1115 Now from what I can see you mount the spacer to the hub on the existing studs with the nuts provided and mount the wheel to the 5 new studs on the spacer with your original n...

I always place axle stands under the rear subframe. Its good and strong and very secure. Its the cross member running across the width of the car between the rear wheels.

Anyone know the location of the fuel filter in a rev 1 na?

Unfortunately through experience I found this is the only way to replace rear ARB's. I just followed the workshop manual step by step and got through it relatively painlessly it does however take a while. I was at it for 4 hours as it was my first time. I reckon I could do it in 2 and a half now i k...

I see thes de-limiters work on the electronic speedos on rev2+ cars what about the rev1 mechanical speedos. Is there a de-limiter available for those or can the electronic one be modified in some way to work?

Cheers Jeff looks kinda daunting but I've rebuild motorbikes from the frame up dozens of times and done some minor stuff on cars in the past few years. I reckon I can get this done if I put my mind to it.
Nice one.
Tony

Ok I have sourced a wheel bearing I just need to get it in before sun when my car is due to be re-tested. I have already done both rear ball joints so im somewhat familiar with the setup back there but i cannot get behind the disk as i dont know/have the right size deep socket to get the axle nut of...

I've been having some problems with my rev1 n/a lately. When i start it up all is fine, runs fine and idles fine about 1200 RPM. Thats when stone cold. Now as the engine starts to get warm about 2/3 mins into a journey it starts to run very rough and hesitates badly. I can be holding a steady thrott...

Item no 43330 in this image http://www.ayrpark.plus.com/epc1/toyota/fullimg.asp/piid=54017&mid=5&cid=215&fulldate=11_01_1993.html is the lower ball joint. Apparently they can be a b1tch to remove. I have to do my rears soon to pass vehicle inspection. Ball joints are available here http:...

[quote="screech205"]That is correct mate, all rear wheel bearings are the same between all revisions and tubby/na. Would have thought fronts are different to rears tho :-k Your right, I phrased that wrong. I meant the fronts are the same across the range and the rears are the same across t...

For the record it looks like the entire range (Turbo and N/A) use the same wheel bearings front and rear. Thats according to my research I stand to be corrected tho.

Anybody???

My Rev1 N/A has just failed its vehicle inspection on its nearside rear wheel bearing and the same side lower ball joint. I have located the ball joint they seem to be the same throughout the range and fairly inexpensive. I can only find this http://www.roguemotorsport.com/forms/Product.aspx?ID=419 ...

I got a sensor off e-bay a month ago cos i kept getting an error code 21. Since I have installed it i've not had any errors. MPG is no better though. Im getting 250ish miles to 50 litres in my rev 1 n/a not great, I'd like more but she's a thirsty motor. The sensor cost £18 plus delivery obviously i...