www.imoc.co.uk

Hello has anyone got a replacement key fob for my transponder
Chip that I could buy pls. It is of the small black, pear shaped type.

Recentley on my k-reg mr2 mk2 2ltr na.... Some dash warning lights have come on constantly. Before they came on permanently they did intermittently flash on and off over the last couple of weeks. The problem lights are as follows; The oil level light, the engine cooling failure light.the battery lig...

Can someone pls explain why my coolent level keeps dropping under the pressure cap but not in the reserve tank?
This doesn't make sense to me. Surely the coolent should run out in the reserve tank before the level drops in the main system!
I am confused pls help.

It cant be for air box as it is plugged in:-(
Seems there is another one on other side... Maybe they are for some kind of upgrade or something?
By the way what does afm stand for? Pls excuse my ignorance!

](*,) On my drive home tonight I noticed a smell of fuel:-( I recenty put this engine in myself and am currently ironing out any 'problems'. I think I have traced the leak to 'around' the fuel fitter area. Could any of these factors contributed to this problem... I filled up for the first time with ...

I have a late 1992 k reg mr2!
Is it a rev1 or 2?
The car I took my engine from was a j reg...it didnt have a charcoal can and many bits looked different under the hood.
Could that have been a rev1?

:thumleft: That is good news, but my car is na! Assuming you realise this by mentioning not using boost. Just wanna check my running temp now pls...should my temp needle be just below half way? Just asking because not sure if thermastat needs changing. Oh...will I get more mpg from shell ultimate? H...

Where exacatly should my temp needle be when at normal running temp, on a 3S ge engine? I just have searched this one to no avail! Mind Sits exacatly half way... But heater never Seems to kick out that much heat. I believe the coolent system is throughly bleeded, but do tell me a way to check this i...

:D Thank you, that Is some solid usefull advice. I just got 250 miles out of my thirst tank of fuel. Used bog standard unleded. Is this about right for my engine? Driving flat back roads...only beaned it half a dozen times for a few seconds, other wize grany style driving! Your help here Is greatly ...

Yes another boring mpg question. My apologies. I replaced my oxy-sensor 2 years ago. Since then the car has been sat untill recently when I replaced the engine due to big end failure. With this replacement engine the mpg seems a little low! Is it possible I may have damaged the sensor while removing...

I am having a lot of trouble removing my front cluster to change sidelight bulb! I am assuming the reflector just behind the side light should pop off, giving me access to a securing screw. Problem is it wont pop off and Looks like the plastic will break if I pull too hard! Pls help, need to do this...

Looks good...i really want to put my 1500 watt bass pusher in my car but there is just no room, besides I sat it on the seat and waked up the gain, my window cracked... Think it wood be to expensive to keep replacing glass every time I get over excited so a smaller set up is due! Wood go down your r...

I need a new flexi welding onto my down pipe. Does anyone have a jig made up for this job?
I am in norfolk/suffolk, can anyone do this job for me at a reasonable price pls?
Many Thanx

Has anyone put 6x9's in the storage boxes behind the seats? If so which way did you face them(up or forwards)? Was it worth it, i.e. Did/does it sound good? I have 2 300w rms 6x9's and a 600w genasis hand built/air cooled amp(will this work under the seat). I want to put some real bass in the car 2....

:evil: ](*,) ](*,) ](*,) I needed to drop my rear bed again today to fit the anti roll bar bushes. Upon doing so one of the longer bolts (looking from rear, the one on left furthest away) broke. It has snapped well up inside the hole with no hope of getting any type of grips on it! I am so gutted ha...

Thanks for your help gents. The problem was that the new cable was stuck in the sheath.
I took it off and greased it up, seems fine now...but shouldn't have been like that, especialy as they are fifty quid each!
Never mind, sorted now, but Thanx again for all your help!

I have all new hand break cables fitted. My problem is that when the break is applied only one side (off side) works. It seems that the other side has more resistance! The arm on the break itself appears fine. I have manually pulled it on by hand. Is this a common problem with the mr2? What can I do...

I have all new hand break cables fitted. My problem is that when the break is applied only one side (off side) works. It seems that the other side has more resistance! The arm on the break itself appears fine. I have manually pulled it on by hand. Is this a common problem with the mr2? What can I do...

Thanx for your help but this method just aint working... Am thinking about forcing compressed air down from the top up tank!

Or maybe some suction on the bleed nipple...

Have pumped and twisted for half an hour to no avail

What say you?

Hello again all... Have recently changed my engine and upon doing so, when I disconnected my clutch flexi to engine I lost quite a bit of fluid:-( My problem is that now I have re-connected every thing I cant seem to bleed the little blighter in! No matter how much I pump and turn the screw I cant s...