www.imoc.co.uk

Hi guys, i need some help getting tyres to fit the wheels that i have going on the car. The wheel spec is as follows: Front: 8.5J, 18", +20 offset, 114.3. Rear 9.5J, 18", +20 offset, 114.3. I am about to buy a full set of staggered Yoko A08R's for the Rev5 but i have no idea what tyre size...

Hi Guys,

Ive got JimGTS's old car with the monster CC setup. Im sure i heard someone on here say that they had plans to fabricate a set of hard polished pipes to replace the samcos? Maybe Tim from xxxx?

If so, please get in touch, as i may want to proceed!!

Yes plse!!
Yhpm

Hi, is this still up for sale, if so plse inbox me.

Thanks!

I took the car to an auto electrician and he installed the head unit out of the mess of wires. The head unit now works but the car won't start. Key turns and the starter relay clicks but there is no 12v charge going to the starter. When you connect the wire running into the starter to a 12v source t...

I will be getting a set, i will report back here assuming my wheels havent come off

Yep, rim should sit 20mm outside rolled arch and stretched tyre will be sitting flush.

I have heard all the horror stories about extended wheels studs with spacers but i have found some ARP ones on twosrus. these are designed for track and racing use so my everyday gentle driving should be ok right? Don't want to compromise on safety but really want to have the right offset on these w...

Hi, I have that spec of wheels. Offset is +30. You'll need to roll the arches unless you have a severe stretch on your tyres. Handles like crap but looks good.Check out pics... http://i341.photobucket.com/albums/o381/adam_and_kim/DSCF4998.jpg http://i341.photobucket.com/albums/o381/adam_and_kim/DSCF...

http://i341.photobucket.com/albums/o381/adam_and_kim/IMG_0226.jpg http://i341.photobucket.com/albums/o381/adam_and_kim/IMG_0225.jpg http://i341.photobucket.com/albums/o381/adam_and_kim/IMG_0224.jpg http://i341.photobucket.com/albums/o381/adam_and_kim/IMG_0223.jpg http://i341.photobucket.com/albums/...

Cheers for all the comments guys, the Lexus rear lights are there as an addition to the red white theme as it's the colours of my company graphics which will be sign written on the car when it's finished, to match the two smart repair vans. I know they are dislked by some (and until a couple of year...

Lexus have no reverse lights, will need to have some in centre panel if you want to include them, i have opted to leave them out, still passed MOT no problem...

Well, after a lot of paint, a new windscreen after the bonnet went through it at 70mph and many hours of toil the car is almost ready. Here are a couple of photos before a final unveiling next week... PS. please excuse the angle of the bonnet, this was taken before it was replaced... http://i341.pho...

Having looked at the previous MOT fail sheet where there was nothing attached at the cat-flexi point the natural idle test gave 0.722% with a limit of <=0.500%, hence a fail, but the car has beenstanding for a very long time (previous MOT was 2006). Test was for a catalyst equipped vehicle with a cl...

That might explain why the wire was cut on the old flexi then!! It should presumably go straight through an MOT then? Might be using pacific works from now on as luke is only down the road.

Ps. Ignore the sig as my turbo was about three cars ago, I have a UK NA

This confused me too. The mechanic i have taken it to says that it needs a 2 wire sensor to attach to the place in the engine that the wire goes. HGowever the flexi pipe i replaced has a 4 wire attached which is wrong. I could really do with some advice on this as its the only thing twarting my MOT ...

I have a rev1 (chassis number <58000) even though its a K plate, and i need a 2 pin lambda sensor as the flexi i bought has a 4 pin. Does anyone know where i could get a 2 pin connector? If not then does anyone know how to connect a 4 pin lambda to a rev 1 engine?

i have been doing something similar with red leatherette and cant get it to stick in the high temps of the car cabin in the sunshine. How has yours held up? What glue did you use?

wheels are 18" 'Godfather' rims, fronts 8.5JJ +30 offset, rears are 9.5JJ +30 offset. Lowered on tein springs on standard struts, clearance to the spring seat is less than 2cm and the clearance to the arch at the rear was less than 2cm until i rolled the rear arches, its still going to be tight...