ive got my brakes apart as one of the sliders was all corroded as the boots werent fitted.... ive bought new boots and tidied/greased up the slider pin etc.
However the new boots wont fit in at all. i tried using a socket as per the DIY but it just crushed and mis-shaped the metal on the new boot.
i got the calipers out and the below are the measurements. seems quite a bit off. now im unsure if its my calipers or the new boots. they were purchased off mr2ben and state theyre suitable for "1989-2000" https://mr2-ben.co.uk/products/668
17.2mm OD new boot
15.5 IDA caliper slider
any ideas where i may have gone wrong?
i used this guide:
forums/kb.php?mode=article&k=190
[Mk2] [Turbo] Brake slider boots dont fit?
Moderators: IMOC Moderators, IMOC Committee Members
[Mk2] [Turbo] Brake slider boots dont fit?
Last edited by rossonza on Mon Sep 24, 2018 12:43 pm, edited 1 time in total.
Re: [Mk2] [Turbo] Brake slider boots dont fit?
You haven't got the remains of the old slider boot metal base still in the carrier, have you? (It certainly looks like it)
EX MR2 owner, currently on a '00 Honda CBR600 Follow me on Instagram @c35rob
Re: [Mk2] [Turbo] Brake slider boots dont fit?
C35Rob wrote:You haven't got the remains of the old slider boot metal base still in the carrier, have you? (It certainly looks like it)
sadly not, theres just the OEM hole for the boots to go into. the new boots do have excess rubber on the underside which you can see. but there is definitely nothing in the hole (old boot etc)
Re: [Mk2] [Turbo] Brake slider boots dont fit?
It does look like the old metal base is still in there (I've made the same mistake myself) give that a few taps with a screwdriver/chisel and a hammer and see if it pops out
EX MR2 owner, currently on a '00 Honda CBR600 Follow me on Instagram @c35rob
Re: [Mk2] [Turbo] Brake slider boots dont fit?
C35Rob wrote:Image Replaced With URL For Quote http://urlur.com/a/z3Vaovu
It does look like the old metal base is still in there (I've made the same mistake myself) give that a few taps with a screwdriver/chisel and a hammer and see if it pops out
ok i completely didn't see/notice that. ill give it a go later. thanks so much!
Re: [Mk2] [Turbo] Brake slider boots dont fit?
Rob. Your a star mate. How on earth did me and my mate miss that??!!
Anyway. I tried getting them out at home. No go. Think I need a vice or some heat.
I owe you a beer Rob
Anyway. I tried getting them out at home. No go. Think I need a vice or some heat.
I owe you a beer Rob
Re: [Mk2] [Turbo] Brake slider boots dont fit?
attempting the removal tonight, will post how it goes.
Re: [Mk2] [Turbo] Brake slider boots dont fit?
well great success... swift hit with a hammer and chisel/flat bladed screwdriver and their out
just got to source new slider pins and the brake clips and then ill have nice refreshed brakes all round.
just got to source new slider pins and the brake clips and then ill have nice refreshed brakes all round.
Re: [Mk2] [Turbo] Brake slider boots dont fit?
new sliders came. jesus the old ones were bad.
-
- Posts: 6213
- Joined: Tue Dec 14, 2004 7:14 pm
- Location: glasgow
- Contact:
Re: [Mk2] [Turbo] Brake slider boots dont fit?
holy moses that is well pitted !
Re: [Mk2] [Turbo] Brake slider boots dont fit?
raptor95GTS wrote:holy moses that is well pitted !
I know!, it looks like the guy that gave me the car had removed the boots before leaving the car to rot in a field.
ive cleaned out the insides of the slider of the carrier, so its nice and smooth and clean with the new pins. but jesus the old ones were shocking weren't they lol.
Re: [Mk2] [Turbo] Brake slider boots dont fit?
Wow. Never seen one that bad!
Be sure to check the bore inside the caliper. They may be unserviceable looking at that!
Be sure to check the bore inside the caliper. They may be unserviceable looking at that!
Re: [Mk2] [Turbo] Brake slider boots dont fit?
Gazza_DJ wrote:Wow. Never seen one that bad!
Be sure to check the bore inside the caliper. They may be unserviceable looking at that!
admittedly that was the worst one.
sorry thats what we cleaned out using a pillar drill, then a dremel attachment with a light sanding disk. the internals nice and smooth and shiny now.
Last edited by rossonza on Fri Oct 05, 2018 9:29 am, edited 1 time in total.
Re: [Mk2] [Turbo] Brake slider boots dont fit?
Have you got the little bushing that goes on the end of the slider as well?
47769-50010
http://japan-parts.eu/toyota/jp/1994/mr ... over#47769
47769-50010
http://japan-parts.eu/toyota/jp/1994/mr ... over#47769
Re: [Mk2] [Turbo] Brake slider boots dont fit?
Gazza_DJ wrote:Have you got the little bushing that goes on the end of the slider as well?
47769-50010
http://japan-parts.eu/toyota/jp/1994/mr ... over#47769
yes Gazza, thanks for the link/part number though