Well... Had a good few days trying to sort my trailing arms out. And I can't get the arm apart. Tried heat. Massive breaker bar. Vice.
Nothings working. Had a look on eBay but they all look similar to mine.
Any recommendations?
Thanks
Ross.
[Mk2] [Turbo] Rear trailing arm options - snapped vice
Moderators: IMOC Moderators, IMOC Committee Members
Re: [Mk2] [Turbo] Rear trailing arm options - snapped vice
Heating and cooling cycles, penetrating fluid, and an impact gun that has some balls. Your average battery powered one won't cut it.
If it's properly corroded then you need to carefully cut the nut off and hope the threads underneath are OK.
If it's properly corroded then you need to carefully cut the nut off and hope the threads underneath are OK.
Re: [Mk2] [Turbo] Rear trailing arm options - snapped vice
Gazza_DJ wrote:Heating and cooling cycles, penetrating fluid, and an impact gun that has some balls. Your average battery powered one won't cut it.
If it's properly corroded then you need to carefully cut the nut off and hope the threads underneath are OK.
Right. May have to cut the nut then. Eeeeek
-
- Posts: 594
- Joined: Wed Feb 16, 2011 8:49 pm
- Location: Leicester
Re: [Mk2] [Turbo] Rear trailing arm options - snapped vice
Run a wire brush on a drill or angle grinder in the exposed threads to clean em out esp into the top of the nut.
Next try a chisel to break the 2 washers apart/away from the bottom of the nut or hacksaw to undercut the nut.
Next heat up and then spray with penetrant (proper penetrant not just wd40)
Then add more penetrant and leave for an hour.
Then rather than leverage use shock, ie an impact gun or podger spanner and hammer
Oh and pray to which ever god floats your boat and curse whatever evil entity you fear
Next try a chisel to break the 2 washers apart/away from the bottom of the nut or hacksaw to undercut the nut.
Next heat up and then spray with penetrant (proper penetrant not just wd40)
Then add more penetrant and leave for an hour.
Then rather than leverage use shock, ie an impact gun or podger spanner and hammer
Oh and pray to which ever god floats your boat and curse whatever evil entity you fear
Re: [Mk2] [Turbo] Rear trailing arm options - snapped vice
Did mine while they were still on the car as I remember these being tough to shift. Just cleaned the threads up with a wire brush and then used a decent impact gun. Took quite a while but it did wind off.
The other side was the same.
The other side was the same.
Re: [Mk2] [Turbo] Rear trailing arm options - snapped vice
Ok thanks guys. My mates got a snapon rattle gun. I'll see if we can give it a try. Maybe a mixture of heat and rattle
Re: [Mk2] [Turbo] Rear trailing arm options - snapped vice
Well.. going my friends tomorrow after work. This came today (didn't realise Amazon prime work bank holidays lol)
So heat and rattle gun using the above is the plan. Wish me luck
So heat and rattle gun using the above is the plan. Wish me luck
Re: [Mk2] [Turbo] Rear trailing arm options - snapped vice
good luck! should be no trouble.
Re: [Mk2] [Turbo] Rear trailing arm options - snapped vice
After a full day of penetration fluid being applied every odd hour. Heat and a breaker bar / rattle gun it all failed.
We moved onto the air chisel and got the nut off
The crush tube was welded on too with rust. It's eaten away a lot of the threads so this arms basically dead. Great.
There's a pair on eBay. I've messaged the guy to ask if the 24mm nuts are free on them. If they are hopefully I'll be sorted soon.
Just frustrated.
We moved onto the air chisel and got the nut off
The crush tube was welded on too with rust. It's eaten away a lot of the threads so this arms basically dead. Great.
There's a pair on eBay. I've messaged the guy to ask if the 24mm nuts are free on them. If they are hopefully I'll be sorted soon.
Just frustrated.
Re: [Mk2] [Turbo] Rear trailing arm options - snapped vice
ebay guys not getting back to me, so presume theyre stuck/he cant be bothered to check them.
since then my friends done a few drawings and i think we may be making our own (hes got a lathe etc in his garage).
could be a fun project
since then my friends done a few drawings and i think we may be making our own (hes got a lathe etc in his garage).
could be a fun project
Re: [Mk2] [Turbo] Rear trailing arm options - snapped vice
Even when they are in good condition these nuts are fairly tight!
Re: [Mk2] [Turbo] Rear trailing arm options - snapped vice
pbmr2 wrote:Even when they are in good condition these nuts are fairly tight!
sure, mine were just too tight, bloody welded on with rust
Re: [Mk2] [Turbo] Rear trailing arm options - snapped vice
well in the end ive had a friend make me some:
Re: [Mk2] [Turbo] Rear trailing arm options - snapped vice
Wow, those look nice. What are they made from, and how much were they?
Re: [Mk2] [Turbo] Rear trailing arm options - snapped vice
Gazza_DJ wrote:Wow, those look nice. What are they made from, and how much were they?
Definately look better than the stock ones i had dont they
These were just a favour, but hes mentioned hes possibly interested if some people on the forum wanted some.
I ordered the following for him to make them from:
Bright round bar steel 22mm dia
Bright mild steel bar 2 inch dia
I've only paid for the metal which was about £30 of off metalmania.
hes doing the welding tonight.