Guide To Replacing T-Bar Seals

Description:

Categories: MR2 Mk2 Articles

Link to this article: Select all

[url=https://imoc.co.uk/app.php/kb/viewarticle?a=130&sid=2d61206812109f961cdca6bbb018cfc6]Knowledge Base - Guide To Replacing T-Bar Seals[/url]

Today I began the process of replacing my 18 year old and leaking t-bar seals. Seeing as this seems to be a much desired option for many t-bar owners, and seeing as I had my camera to-hand, I thought I’d make a step-by-step guide.

If anyone has any tips or hints they feel would be useful, again just add them below.

___________________________________________________________

Firstly, replacement t-bar seals can be purchased from a Toyota parts dealer in Dallas, USA. You need all four parts listed below. The 'weatherstrips' are the seals that attach to the car around the window and t-bar glass. The 'glass t-bar panel seals' go on the actual t-bar panel itself. Search by part number:

63627-17022 (Weatherstrip for T-Bar) Drivers Side
63628-17022 (Weatherstrip for T-Bar) Passenger Side
62381-17051 (Glass t-bar panel seal) Drivers Side
62382-17051 (Glass t-bar panel seal) Passenger Side

...via this link:

http://www.toyotapartsales.com/partloca ... eid=214074

All in, mine came to about £230, plus another £17 import duty upon arrival in the UK about a fortnight later. Their prices seem to change often but it’s still cheaper than Toyota here in the UK!

When the seals arrived, I hung them up in the shower and sprayed half a can of Halfords silicone sealant over them and left them to dry for two days. This ensures they’re water tight and replenished after sitting in storage for a while.

Ok, here’s what I did.

Firstly, pull the handle down and remove the little ‘nub’ (indicated) by giving it a firm pull.

Image

The next fit is a bit fiddly. You need to remove the golden cir-clip from the hinge of the handle. I did this with a flat-head screw driver and a bit of patience. Once removed, pull the handle outwards and it should just slide off.

Image

Remove the screw from both ends of the panel.

Image

… and gently remove the plastic cover. This is attached via two concealed clips which just pop out. A bit of force is needed. But be careful, it only plastic after all.

Image

Next, remove the three red bolts using a 10mm socket. To gain access to the top one, you may need to bring the bars inwards (as shown in green). Once removed, bring those ‘green’ bars inwards so that you can remove the mechanism completely.

Image

Image

Remove this screw from both ends of the t-bar panel.

Image

… and remove the rod guiders from both ends also.

Image

Next is the removal of the old t-bar rubber. This is attached with bonding sealant and requires a bit of force to remove.

Image

Then with an abrasive cloth or similar, clean up the surface.

Image

Here’s a comparison between the old, worn rubber and the plump new one.

Image

Next, take your new t-bar rubber. Make sure it is for the same side of the car as they are not interchangeable. As shown below, these are not for the same side! So be careful.

Image

The new rubber will have paper protecting the pre-applied adhesive.

Image

At this point, with the paper still attached, I laid the rubber in situ so that I could see how it fitted to the panel itself.

Image

Once I was happy with how it fitted together, I grabbed myself a can of silicone-based adhesive:

Image

… and applied a small amount as shown:

Image

Now it’s time to fix the new rubber to the panel. Remove the paper covering the pre-applied adhesive, and lay the rubber on to the panel like you did in the ‘practice run’. Press down in all areas where adhesive is located.

Ensure the screw holes at both ends line up. If not, gently manoeuvre the rubber until it does. The adhesive does not dry for many hours so you have time to adjust things.

Image

I noticed the following parts of rubber were not very well secured to the glass panel, so added a small amount of adhesive underneath:

Image

Once you’re happy with the fit, re-fit the rod guides followed by the flatter-headed of the screws:

Image

Image

Reattach the mechanism and fasten the red bolts. Be careful not to over-tighten these bolts as they strip easily (as I found out).

Image

Image

Attach the plastic covering. This is done by ensuring the ‘nub’ is located first (shown below).

Image

Fasten the remaining two screws, one at either end:

Image

Attach the nub:

Image

With the cir-clip in situ, attach the handle as shown. Note that the protruding rods/prongs at either end of the panel must, at this point, be retracted.

Image

Image

The finishing touch for me was applying an additional small dab of adhesive to the indicated area to ensure a secure fit and finish.

Image

Now do the same on the other panel.



___________________________________________________________
***********************************************************



Ok, now for replacing the rubber t-bar seals that fix to the car itself.

The following is for the passenger side.

Firstly, starting at the back section of the seal, using a flat-head screwdriver, pop out the two studs/poppers, and free the small metal ‘L’ shaped clip (hidden behind where the far left arrow is pointing).

Image

You should then be able to pull the seal away from the body. Some areas are attached with adhesive, but should detach quite easily.

Image

The next section of the seal is bolted to the body of the car. This image shows the new t-bar seal to indicate where the bolts are located:

Image

With a flat-head screwdriver, bring the plastic moulding forwards so that it passed over and in front of the bracket.

Image

You need to remove the bracket by unscrewing two bolts using a 10mm socket. Be very careful not to drop the bolts as they will disappear behind the speakers and you may never see them again!

Image

With the bolts removed, a bit of force will free the seal.

Image

Working your way towards the centre of the roof, remove the two screws.

Image

…and remove the wind deflector, held on by two screws.

Image

You now need to remove the front bracket in the same way you removed the rear one.

Image

Pull the seal away from its location until you reach the door hinge section.

Image

Here, you need to remove the two studs/poppers like you did at the rear.

Image

With the old t-bar seal fully removed, go around with a damp cloth and thoroughly clean all the newly exposed paintwork of moss, grime and general crud.

Image

As is commonly the case, removing the 15-20 year old seals is likely to reveal some rust spots. Here, I cleaned up the rust by removing as much of it as I could before surrounding the area with silicone adhesive. This ensures that when the new seals are in place, no water can return to the affected area. I applied the adhesive where shown in red:

Image

Attach the new seal starting at the centre of the roof.

Image

With a flat-head screwdriver, go along and ensure the seal overlaps the roof lining as shown:

Image

Now, ensure the corner lines up with the body work as shown. Do the same for the front corner also.

Image

I added some additional sealant under the rubber as shown in red to ensure a better seal.

Image

Remove the tape covering the adhesive on the new seal, relocate the metal ‘L’ bracket and pop the two studs in to place. Push down where the adhesive is to ensure a tight seal.

Image

Again, armed with your flat-head screwdriver, run along the edge of the seal (highlighted in yellow) and ensure the ‘flap’ slots in behind the ledge.

Image

Do the same with the front section also.

Image

Your passenger side t-bar seal is now fitted. Just need to do the other side!

I did notice that the roof panel sits a bit higher than it did previously. This is obviously due to the plumpness of the new rubbers. As a result, the top of the window doesn't create a tight seal against the rubber of the roof panel. So the next stage for me is to adjust my window so that it sits flush against the new rubber.


:thumleft: